This manual (OEM #97897-12553) stays with one tractor family across all 563 pages: the M4900, M5700, and M5700HD, from engine internals to cabin A/C. You'll find wiring diagrams for ROPS, cabin (USA and Canada), and body harness layouts, plus hydraulic schematics tracing the three-point system, power steering circuit, and auxiliary control valve. There are 26 pages of troubleshooting charts spanning every major system, 10 pages of torque tables, maintenance intervals from daily checks through 3,000-hour service points, and 100 pages of step-by-step rebuild procedures. Torque the cylinder head screws to 93.1-98.0 N-m (68.7-72.3 ft-lbs) and swap the fuel filter element every 200 hours; both figures come straight from the factory, not a forum thread. Machine down in the field? Open your copy on any device, search by keyword, and get the answer before the next bolt turns.
What's Inside This Kubota M4900, M5700, M5700HD Manual
| System | Pages | Key Topics |
|---|---|---|
| Safety Instructions | 3-9 | - |
| Specifications | 10-14 | Model, Engine, Dimensions, Weight, Travelling system, Hydraulic system |
| General | 15-72 | Features, Tractor Identification, Handling Precautions For Electrical Parts And Wiring (Battery, Fuse, Connector, Handling of Circuit Tester), Lubricants, Fuel And Coolant |
| Engine | 73-150 | Features, Engine Body, Cylinder Block, Cylinder Head, Crankshaft, Piston And Piston Rings, Connecting Rod, Camshaft |
| Clutch | 151-184 | Travelling Clutch, PTO Clutch, Clutch Pedal, Clutch Disc, Diaphragm Spring, Clutch Lever |
| Transmission | 185-233 | Structure, Shuttle Shift Section (Forward-Reverse), Main Gear Shift Section, Hi-Lo, Creep Shift Section, Four Wheel Drive Section (4WD Only), Pto System, Differential Gear |
| Rear Axle | 234-245 | Features, Final Reduction System, Changing Transmission Fluid, Lift Rods and Lower Links, Rear Wheel, Fender and Foldable ROPS, Rear Axle Case, Disassembling Planetary Gear |
| Brakes | 246-260 | Features (Wet Disc Brakes, Stable Braking, Pedal Stroke Does Not Change Under Influence of Heat, Fade), Operation (During Braking), Troubleshooting, Servicing Specifications |
| Front Axle | 261-286 | Structure (Wheel Drive Type), Front Wheel Alignment (Camber, Kingpin Angle, Caster, Toe-in), Troubleshooting, Servicing Specifications (2WD Type, 4WD Type), Tightening Torques |
| Steering | 287-313 | Steering Linkage, Power Steering Hydraulic Circuit, Power Steering System Hydraulic Pump, Steering Controller (Control Valve, Metering Device, Oil Flow), Steering Cylinder |
| Hydraulic System | 314-353 | Three Point Hydraulic System, Hydraulic Pump, Oil Filter, Position Control Valve, Relief Valve, Hydraulic Cylinder |
| Electrical System | 354-429 | Wiring Diagram (Rops Type, Cabin Type, Body Harness) |
| Cabin | 430-499 | Air Conditioner System |
Quick Reference Specifications
| Specification | Value | Page |
|---|---|---|
| Cylinder head screw tightening torque | 93.1 to 98.0 N-m (9.5 to 10.0 kgf-m, 68.7 to 72.3 ft-lbs) | p. 115 |
| Hydraulic system troubleshooting solutions | No specific 'reset' procedure or value found. Solutions include 'Repair or replace' or 'Adjust'. | p. 335 |
| Fuel filter element replacement frequency | Every 200 Hours | p. 28 |
| Fuel filter performance (particle size at pressure) | 15 microns (0.00059 in.) at 20 kPa (0.2 kgf/cm², 3 psi) | p. 89 |
| Engine oil filter replacement frequency | Every 200 Hours | p. 28 |
| Hydraulic oil filter replacement frequency | Every 400 Hours | p. 28 |
| Radiator hose replacement frequency | Every 2 Years | p. 28 |
| Hose clamp tightening instruction | Tighten securely (no specific torque value provided) | p. 37 |
| Battery voltage | More than 12 V | p. 407 |
| Battery terminal connection potential difference | Less than 0.1 V | p. 407 |
| Foldable ROPS mounting screw torque (M16, grade 9) | 259.9 to 304.0 N-m (26.5 to 31.0 kgf-m, 192.0 to 224.0 ft-lbs) | p. 27 |
| Gaskets and O-rings replacement instruction | Must be replaced during reassembly (no specific numerical values provided) | p. 20 |
Kubota M4900, M5700, M5700HD Common Problems This Manual Covers
Engine cranks but hard-starts, loses power, or runs rough under load on the M4900, M5700, or M5700HD. p. 28
Inspect the fuel filter element and replace it if it is past the 200 Hours interval noted on page 28. Confirm the filter still meets its 15 microns (0.00059 in.) rating at 20 kPa (0.2 kgf/cm², 3 psi). Drain the system and bleed air from the fuel lines.
Manual Section: Engine TroubleshootingThree-point hitch implement lifting functions are weak, slow, or exhibit intermittent movement during field operation. p. 335
Check the hydraulic oil filter and replace it if it has run past the every 400 Hours service interval. Confirm pump output matches the 41.6 L (44.0 U.S.qts., 36.6 Imp.qts.)/min capacity. Inspect the fittings and adjust the implement linkages per the troubleshooting steps on page 335.
Manual Section: Hydraulic System TroubleshootingCooling system overheating, coolant loss, or temperature instability after idling or running at high RPM. p. 36
Measure the fan belt deflection and confirm it falls within 7 to 9 mm (0.28 to 0.35 in.), the figure given on page 36. Inspect the radiator hoses for cracking and replace any older than 2 Years. Tighten every hose clamp to stop coolant leaks under pressure.
Manual Section: Engine TroubleshootingStarter relay clicks but engine fails to turn over or exhibits sluggish electrical starting performance. p. 407
Test the battery voltage across the terminals; it should read more than 12 V, as covered on page 407. Clean the posts and cable clamps. Measure the potential difference across the terminal connection and check that it stays less than 0.1 V for proper current flow.
Manual Section: Electrical System TroubleshootingFrequently Asked Questions
What are the torque specs for Kubota M5700 wheel lug nuts?
Rear wheel mounting nuts on the M5700 take 260 to 304 N·m (26.5 to 31.0 kgf·m, 192 to 224 ft-lbs). Front wheel mounting nuts, on both 2WD and 4WD models, torque to 166.7 to 196.1 N·m (17.0 to 20.0 kgf·m, 122.3 to 144.6 ft-lbs).
What are the torque specs for Kubota M4900 head bolts?
On the Kubota M4900, the cylinder head screws (also called head bolts) tighten to 93.1 to 98.0 N·m (9.5 to 10.0 kgf·m, 68.7 to 72.3 ft-lbs). Getting this figure right matters for a proper engine assembly.
How quickly can I access this Kubota M4900, M5700, M5700HD manual after buying?
A 563-page Service Manual in searchable PDF, ready the moment your checkout completes. Open it on a computer, tablet, or phone, with no shipping wait.
Is this Kubota M4900, M5700, M5700HD Service Manual printable?
None at all. The PDF is DRM-free, so print whatever sections you want to carry out to the shop. Standard letter or A4 paper both work.
Does this Kubota M4900, M5700, M5700HD manual cover the hydraulic system?
Yes. The hydraulic schematics map every circuit, control valve, and component spec for the Kubota M4900, M5700, and M5700HD.
Document Quality
This is a scanned PDF document with an OCR text layer. You can search and copy the full text, and the text itself is crisp and easy to read throughout. Diagrams and illustrations are clear scanned images, not vector graphics, but all labels are perfectly readable. Pages are clean with no noticeable scan artifacts, stains, or skewed content. There are several blank title pages separating sections, which serve as dividers.
Reviews
There are no reviews yet.