Pull the T1700H or T1700HX apart with the people who built it looking over your shoulder. Across 27 pages, this Kubota workshop manual documents every hydrostatic transaxle teardown, brake adjustment, and front axle rebuild, with hydraulic schematics that trace oil flow in neutral, forward, and reverse through the ball piston pump and motor. Ten pages of tightening torques and six pages of exploded views cover the hydrostatic transaxle, reduction gear, and parking brake. Turn to disassembly for step-by-step procedures: separating the transmission from the rear axle, checking and adjusting the brake, and rebuilding the front axle from the ground up. Torque the transaxle mounting screws to 48.1-55.9 N-m and refill the transaxle with 2.4 liters before you button it back up. Everything is bookmarked and searchable, so any spec is one keyword away in the shop.
What's Inside This Kubota T1700H, T1700HX Manual
| System | Pages | Key Topics |
|---|---|---|
| Safety Instructions | 3-4 | Safety Decals Overview, Warning Decals, Caution Decals, Danger Decals |
| Specifications | 5-6 | Engine Specifications (Model and Type, Dimensions and Performance, Systems, Fluids and Weight) |
| M. Mechanism | 7-14 | Clutch And Transmission (Hydrostatic Transaxle: Overview, Components), Ball Piston Pump (Description, Operation), Ball Piston Motor (Description |
| S. Disassembling And Servicing | 15-27 | General (Lubricants And Fuel, Servicing Specifications, Tightening Torques, Check And Maintenance) |
Quick Reference Specifications
| Specification | Value | Page |
|---|---|---|
| All Models | ||
| Hydrostatic transaxle mounting screw torque | 48.1 to 55.9 N-m (4.9 to 5.7 kgf-m, 35.4 to 41.2 ft-lbs) | p. 19 |
| Rear wheel mounting screw torque | 23.5 to 27.5 N-m (2.4 to 2.8 kgf-m, 17.4 to 20.3 ft-lbs) | p. 19 |
| Hydrostatic Transaxle capacity | 2.4 l (2.5 U.S.qts., 2.1 Imp.qts.) | p. 16 |
| Engine Fuel capacity | 9.5 l (2.51 U.S.gals., 2.09 Imp.gals.) | p. 5 |
| Hydrostatic Transaxle oil change interval | Normally, hydrostatic transaxle oil does not need to be changed. | p. 16 |
| Engine Total Displacement | 535 cc | p. 5 |
| Engine Maximum Horsepower (Gross) | 17 HP / 3600 rpm | p. 5 |
| Brake Spring Clearance | 0 to 1 mm | p. 16 |
| Neutral Adjuster Retaining Screw Torque | 18.6 to 24.5 N-m | p. 16 |
| Front Axle Center Bolt Retaining Nut Torque | 62.8 to 72.6 N-m | p. 16 |
| T1700H | ||
| T1700H Overall Length | 1705 mm | p. 6 |
| T1700HX | ||
| T1700HX Overall Length | 1732 mm | p. 6 |
Kubota T1700H, T1700HX Common Problems This Manual Covers
Kubota T1700H hydrostatic transaxle creeps forward or backward with pedal released p. 20
Adjust the neutral position using the procedure on page 20. Loosen the neutral adjuster retaining screw, reposition the neutral lever until rear wheel rotation stops with the pedal fully released, then torque the retaining screw to 18.6 to 24.5 N-m. Test in both forward and reverse before returning the machine to service.
Manual Section: Hydrostatic Transaxle Neutral AdjustmentTractor won't move in forward or reverse, drive pedal depresses but nothing happens p. 20
Inspect the drive belt first for cracking, glazing, or slipping off the pulley. If the belt is good, raise the rear wheels and run the transaxle performance check on page 20 at full pedal travel. A transaxle that spins freely under full load with no resistance has internal wear and needs assembly replacement.
Manual Section: Hydrostatic Transaxle Performance CheckRear wheels slip or lose traction under load on slopes and wet terrain p. 20
Raise the rear of the machine and run the slip check on page 20 with the pedal at full travel. Verify both wheels resist rotation under load. Check all rear wheel mounting hardware for looseness before condemning the transaxle. If slip persists with fasteners tight and load applied, replace the transaxle assembly.
Manual Section: Hydrostatic Transaxle Performance CheckBrake pedal travels too far before engaging, machine rolls on incline when parked p. 25
Check brake spring clearance at page 25. With the brake fully released, clearance must measure 0 to 1 mm. Adjust the brake rod until within spec, then confirm the parking brake holds the machine stationary on a grade. Verify the safety switch setting length is correct before returning to service.
Manual Section: Brake System Check and AdjustmentSteering pulls to one side, front wheels track unevenly on flat ground p. 26
Measure front wheel toe-in and adjust per the procedure on page 26. Set the tie-rod to bring toe-in within spec, then torque the tie-rod lock nut to 39.2 to 45.1 N-m. If binding or play persists after adjustment, remove the front axle and inspect the knuckle shaft and knuckle arm for wear.
Manual Section: Front Axle Toe-in AdjustmentFrequently Asked Questions
What fluids and capacities does this machine require?
Fuel is automobile unleaded gasoline, 9.5 l (2.51 U.S.gals., 2.09 Imp.gals.). Engine oil is API service SE or SD class, 1.6 l (1.7 U.S.qts., 1.41 Imp.qts.). The hydrostatic transaxle takes API service CD SAE 20W-30, 2.4 l (2.5 U.S.qts., 2.1 Imp.qts.), and that oil normally never needs changing.
What are the hydraulic system specifications?
A variable displacement ball piston pump drives the hydrostatic transaxle, paired with two fixed displacement ball piston motors. It runs on API service CD SAE 20W-30, capacity 2.4 l (2.5 U.S.qts., 2.1 Imp.qts.). Oil flow is mapped for neutral, by-pass lever, forward, and reverse operation.
What torque specifications are listed?
Several are documented. The rear wheel mounting screw takes 48.1 to 55.9 N-m (4.9 to 5.7 kgf-m, 35.4 to 41.2 ft-lbs); the front axle center bolt retaining nut takes 62.8 to 72.6 N-m (6.4 to 7.4 kgf-m, 46.3 to 53.5 ft-lbs). The transaxle mounting screw runs 48.1 to 55.9 N-m, and the neutral adjuster retaining screw 18.6 to 24.5 N-m.
How will I receive this Kubota T1700H, T1700HX Workshop Manual?
Download is immediate: the complete 27-page searchable workshop manual, ready to open on any device, from the laptop at your desk to a phone out in the field.
Am I able to print pages from this Kubota T1700H, T1700HX manual?
Yes. The PDF carries no DRM restrictions, so you can print any page or section you need for the shop on any standard printer.
Are hydraulic system diagrams in this Kubota T1700H, T1700HX Workshop Manual?
Yes. The manual includes hydraulic circuit diagrams, system schematics, and component specifications with pressure ratings.
Document Quality
This document is a scanned PDF, not a native digital file. An OCR layer has been applied, allowing you to search and copy the full text, though the original scanned text sometimes exhibits minor fuzziness. Diagrams and illustrations are raster images, not vector, but their labels remain readable. Page conditions are generally clean, with only minor scan artifacts and slight skewing present on some pages. All pages contain content, with no notable blank or filler pages.
Reviews
There are no reviews yet.