OEM #11770 covers the Kubota B1700, B2100, and B2400 compact tractors, including HSD, HSDB, D, and B2400 HSE variants, across 454 bookmarked pages. You get 10 pages of wiring diagrams, 10 pages of hydraulic schematics, and 150 pages of step-by-step procedures across engine, clutch, transmission, rear axle, brakes, front axle, steering, and mower deck. Add 10 pages of torque tables, 15 pages of troubleshooting, and a 50-page exploded view set for parts ID. Cylinder head bolts torque to 63.7 to 68.6 N·m (47.0 to 50.6 ft-lbs). Swap the hydraulic filter cartridge at 50 hours, then every 300. Tap the bookmark, find the spec, finish the job.
What's Inside This Kubota B1700–B2400 Series Manual
| System | Pages |
|---|---|
| General | 10-53 |
| Sect 1 Engine | 54-123 |
| Sect 2 Clutch | 124-139 |
| Sect 3 Transmission | 140-204 |
| Sect 3 Transmission Supplement Bi Speed Turn | 205-239 |
| Sect 4 Rear Axle | 240-249 |
| Sect 5 Brakes | 250-263 |
| Sect 6 Front Axle | 264-281 |
| Sect 7 Steering | 282-305 |
| Sect 8 Hydraulic | 306-331 |
| Sect 9 Electrical | 332-381 |
| Mower | 382-417 |
| Enhanced Model Supplement | 418-454 |
Quick Reference Specifications
| Specification | Value | Page |
|---|---|---|
| Cylinder head bolt | 63.7 to 68.6 N·m, 6.5 to 7.0 kgf·m, 47.0 to 50.6 ft-lbs | p. 83 |
| Hydraulic oil filter cartridge replacement | Initial 50 hours, then every 300 hours | p. 21 |
| Engine oil filter cartridge replacement | Initial 50 hours, then every 200 hours | p. 21 |
| Fuel filter element replacement | Every 400 hours | p. 21 |
| Fuel filter bracket mounting screw | 17.7 to 20.6 N·m | p. 83 |
| Air cleaner element replacement | Once yearly or after every sixth cleaning | p. 29 |
| Glow plugs | 7.8 to 14.7 N·m, 0.8 to 1.5 kgf·m, 5.8 to 10.8 ft-lbs | p. 83 |
| Mica Undercut | 0.2 mm | p. 359 |
| Brake Disc Thickness | 3.0 mm | p. 256 |
| Friction Plate Thickness | 1.52 mm | p. 256 |
| Flare nut (P.S. pipes and 3-point hitch delivery pipe) | 29.4 to 39.2 N·m | p. 83 |
| PTO Power | 9.7 kW (13.0 HP) | p. 5 |
Kubota B1700–B2400 Series Common Problems This Manual Covers
Hydrostatic transmission will not move forward or reverse after a fluid change on the B2100
Confirm transmission oil is at the 12.0 L (3.17 U.S. gals) capacity on page 24. Pull and clean the HST suction screen. Bleed trapped air by idling the engine and cycling the forward/reverse pedal 10 times. Pressure-test the charge pump using the troubleshooting steps in the transmission section if symptoms persist.
Manual Section: Sect 3 Transmission3-point hitch raises slowly or settles under implement weight when parked p. 318
Top hydraulic oil to the dipstick full mark. Look over the lift cylinder and control valve for external seepage. Tighten the 3-point delivery pipe flare nuts to 29.4 to 39.2 N·m. Run the relief-valve pressure test on page 318 and swap the filter cartridge if the implement still hunts or drops.
Manual Section: Sect 8 HydraulicStarter clicks but engine will not crank after sitting overnight p. 356
Read battery voltage at the terminals and replace anything below 12.4V at rest. Scrub cable ends and the ground strap down to bare metal. Continuity-test the seat switch, PTO interlock, and neutral start switch against the wiring diagram on page 334. Verify mica undercut at 0.2 mm if you bench-test the starter.
Manual Section: Sect 9 ElectricalEngine overheats during mowing in tall grass or hot weather
Shut down and let it cool. Pop the screen and blow radiator fins clean from the fan side at under 200 kPa. Top the coolant cold. Belt deflection at midspan should sit at 7 to 9 mm; tweak the alternator bracket if it is loose. Verify thermostat opening temperature using the engine troubleshooting steps.
Manual Section: Sect 1 EngineBrake pedal travels too far or tractor pulls to one side when stopping p. 256
Pull the brake covers and gauge friction plate thickness, replacing anything under 1.52 mm. Compare brake disc thickness against the 3.0 mm wear limit on page 256. Look for oil contamination from the rear axle seal on the friction surfaces. Set pedal free play equally on both sides, then road-test against the uneven braking chart on page 256.
Manual Section: Sect 5 BrakesSteering wheel has excessive play or feels heavy at low engine speed p. 292
Jack the front axle and wiggle the tie rod ends for radial play. Set toe-in to spec. Look over the front axle pivot bushings and kingpins for wear. Tighten front wheel mounting nuts to 77 to 90 N·m. Run the power-steering relief pressure test on the chart on page 292 if the wheel will not return to center.
Manual Section: Sect 7 SteeringFrequently Asked Questions
How do I reset the Kubota B1700/B2100/B2400 PTO or safety switches?
Run the safety system tests on page G-15 first. If the engine cranks during any test, the corresponding switch needs adjustment or replacement. Each linkage must sit in its specified condition during the work (for example, clutch pedal fully depressed). Set safety switch distance 'A' to the factory spec of 17 to 21 mm (0.67 to 0.83 in.).
What are the torque specs for Kubota B1700/B2100/B2400 wheel nuts, head bolts, and axle components?
Front wheel mounting nuts: 77 to 90 N·m (57 to 67 ft-lbs). Rear wheel hub mounting nuts: 108 to 125 N·m (80 to 93 ft-lbs). Cylinder head bolts: 63.7 to 68.6 N·m (47.0 to 50.6 ft-lbs). Front axle frame mounting screw: 39.2 to 64.7 N·m (28.9 to 47.7 ft-lbs).
What do I do if my Kubota B1700/B2100/B2400 will not start and the stop solenoid is not receiving power?
Start by checking lead terminal voltage at the fuel cut-off solenoid. With the main switch ON, measure across terminal 3 (red, black) of the wiring harness to chassis. Battery voltage of 11 to 14 V should be present. If it is not, the manual points to a faulty fuse, main switch, or wiring harness needing inspection or replacement.
How to reset Kubota B1700 HSD safety switch
Run the tests on page G-15. If the engine cranks when it should not, adjustment is required. Set safety switch distance 'A' (shown in the diagram) to the factory spec of 17 to 21 mm (0.67 to 0.83 in.). The associated linkage, such as the clutch pedal, must be in the correct position while you adjust.
What do I get after purchasing this Kubota B1700, B2100D manual?
A 454-page searchable PDF ready for immediate download. Works on any device, so you can pull it up on your phone while under the hood. No shipping, no waiting.
Is this Kubota B1700, B2100D Shop Manual printable?
Yes, print as many copies as you want with no restrictions. Many mechanics print the section they need and take it out to the shop floor.
Are hydraulic system diagrams in this Kubota B1700, B2100D Shop Manual?
Yes. The manual includes hydraulic circuit diagrams, system schematics, and component specifications with pressure ratings.
Document Quality
This is a scanned copy of a physical workshop manual, and a text layer has been added, allowing you to search the document and copy text. The text quality is generally clear and legible, though it's not as crisp as a native digital file. Diagrams are a mix of raster line drawings and photographs; the line drawings are clear with readable labels, while the photos are a bit grainy but still functional for identifying parts. The pages are mostly clean, with some minor specks and occasional slight page skew, and you will find several blank pages that likely served as section dividers.
Reviews
There are no reviews yet.