Factory-written for the BX1880-AU, BX2380-AU, and BX2680-AU tractors plus their full rotary mower lineup (RCK60D-26BX, RCK54-23BX, RCK60B-23BX, RCK48-18BX), this 456-page Workshop Manual carries OEM #9Y111-18054. It runs 52 pages of hydraulic schematics that route the steering, loader, and lift circuits, then 4 pages of wiring diagrams with a connector chart for every relay, safety switch, and OPC circuit. Another 20 pages walk troubleshooting across engine, transaxle, hydraulic, and mower systems, backed by 10 pages of torque tables and exploded views of the hydrostatic transaxle and gearbox. Blade screws spec at 103-117 N·m, the outer pulley nut at 197-225 N·m, both printed here rather than guessed off a forum. When the machine is down, open this bookmarked PDF on any device and jump to the section you need.
What's Inside This Kubota BX1880-AU & variants Manual
| System | Pages | Key Topics |
|---|---|---|
| Record of Revisions | 3-18 | - |
| Information | 19-41 | - |
| General | 42-128 | Tightening Bolts and Nuts, Applying Thread-Locking Fluid, Installing Circlips, Installing Spring Pins, Handling Split Pin, Handling Chain Joint and Split Pin |
| Engine | 129-209 | Engine Body, Function of Cylinder Block, Function of Closed Breather, Function of Half-Floating Head Cover, Function of Piston, Function of Piston Ring, Function of Connecting Rod, Function of Crankshaft |
| Transaxle | 210-272 | Mechanism, Structure of Transaxle, Traveling System (Hydrostatic Transmission, Range Gear Shift Section, Front Wheel Drive Section, Differential Gear Section, Brake Section) |
| Front Axle | 273-291 | Mechanism, Structure of Front Axle, Front Wheel Alignment (Camber of Front Axle, Kingpin Angle of Front Axle, Caster of Front Axle, Toe-in of Front Axle), Servicing |
| Steering | 292-308 | Mechanism, Structure of Steering System, Hydraulic Circuit of Steering, Steering Controller (Structure of Steering Controller, Control Valve, Metering Device, Relief Valve) |
| Hydraulic System | 309-361 | Mechanism, Structure of Hydraulic System, Hydraulic Circuit, Hydraulic Pump (Outline of Hydraulic Pump, Structure of Hydraulic Pump, Specification of Hydraulic Pump) |
| Electrical System | 362-418 | Mechanism, Wiring Diagram of BX Tractor, Electrical Connector Chart |
| Mower | 419-456 | Mechanism, Structure of Power Transmission of Mower, Structure of Lifting Mechanism of Mower, Structure of Self-Balancer System of Mower, Servicing, Troubleshooting for Mower |
Quick Reference Specifications
| Specification | Value | Page |
|---|---|---|
| Mower blade screw torque | 103 to 117 N·m, 10.5 to 12.0 kgf·m, 76.0 to 86.7 lbf·ft | p. 426 |
| Gear box mounting screw torque | 78 to 90 N·m, 7.9 to 9.2 kgf·m, 58 to 66 lbf·ft | p. 426 |
| Mower belt replacement condition | if there is found surface split at more than 3 positions | p. 439 |
| Pulley boss mounting nut torque | 24 to 27 N·m, 2.4 to 2.8 kgf·m, 18 to 20 lbf·ft | p. 426 |
| Three spindle shafts greasing interval | Daily check | p. 71 |
| Three spindle shafts greasing amount | Until grease overflows | p. 63 |
| Gear box oil seal check interval | Every 1 year | p. 71 |
| Gear box oil seal replacement interval | Every 4 years | p. 71 |
| Air cleaner element check interval | Every 100 Hr | p. 69 |
| Air cleaner element replacement interval | Every 1000 Hr or 1 year | p. 69 |
| Radiator screen cleaning instruction | Remove the radiator screen, and then remove all the foreign material. | p. 75 |
| Greasing interval (BX tractor) | Every 50 Hr | p. 69 |
Kubota BX1880-AU & variants Common Problems This Manual Covers
Kubota BX tractor engine overheats under mowing load, temperature gauge climbs into red p. 146
Pull the radiator screen and clear every bit of debris, per page 75. Top up coolant if it sits low, and check the fan belt for cracks or slack. Confirm engine oil reaches the full mark; crankcase capacity runs from 3.0 L on the BX1880-AU to 4.0 L on the BX2680-AU with filter. If it still climbs, work the troubleshooting chart on page 146.
Manual Section: EnginePTO shaft spins after deck connection but mower blades stay stationary, no cutting action p. 424
Verify every mower coupler latch clicks firmly home; a half-seated connection won't carry drive. Confirm the PTO switch is on and the seat-based operator presence control is active. Inspect gearbox oil level and change it if overdue, since the interval is every 150 hours. Mower troubleshooting starts on page 424.
Manual Section: MowerMower drive belt squealing or slipping, cut height inconsistent across full deck width p. 439
Run an eye along the full length of the belt and replace it once surface splits show at more than 3 spots, per page 439. Make sure each pulley spins freely and the belt seats in every groove. With the new belt on, torque the outer pulley mounting nut to 197 to 225 N·m (145 to 166 lbf·ft), per page 426.
Manual Section: MowerExcessive vibration felt through seat and steering during mowing, rough or grinding noise from deck p. 63
Grease all three spindle shafts before every mowing session, pumping until grease overflows the fitting, per page 63. If the shaking persists, drop the deck and spin each spindle by hand; roughness or noise means a worn bearing. After any blade or spindle work, torque the blade screw to 103 to 117 N·m (76.0 to 86.7 lbf·ft), per page 426.
Manual Section: MowerHydraulic quick coupler leaks at the connection point or won't lock after connecting p. 359
Wipe both coupler faces and check the O-ring seat for nicks or grit before connecting. Thread the cartridge to finger tight, then add 2 to 3 turns with a cartridge socket, per page 359. Should seepage continue after correct seating, pull the O-rings and swap any that look cracked, flattened, or cut.
Manual Section: Hydraulic SystemEngine cranks but won't fire, or turns over slowly and fails to start in cold conditions p. 144
Start with fuel level: the tank holds 25 L (6.6 U.S.gals). Make sure the operator presence control seat switch is active and the main switch is fully on. In the cold, test battery voltage and trace the starter circuit with the electrical troubleshooting steps. When cranking is strong but it won't fire, work the no-start sequence.
Manual Section: EngineFrequently Asked Questions
How will I receive this Kubota BX1880-AU & variants Workshop Manual?
Download lands instantly. The full 456-page searchable Workshop Manual is yours the moment payment clears, ready to open on a laptop, tablet, or phone right at the bench.
What is the mower blade screw torque spec for the Kubota BX1880-AU mower deck?
The manual gives the mower blade screw torque as 103 to 117 N·m, 10.5 to 12.0 kgf·m, or 76.0 to 86.7 lbf·ft (page 426). It also lists the gear box mounting screw torque as 78 to 90 N·m (58 to 66 lbf·ft) on the same page. Use these values after any blade or deck service to seat the hardware correctly.
How often should the mower spindle shafts be greased on these BX models?
The manual calls for a daily check of the three spindle shafts, greasing them until grease overflows the fitting (pages 71 and 63). Keeping up with this prevents the seat and steering vibration that points to a worn spindle bearing, with deck troubleshooting starting on page 424. Skipping it is a common cause of rough, noisy mowing.
What are the air cleaner element service intervals for the Kubota BX1880-AU?
Check the air cleaner element every 100 hours and replace it every 1000 hours or 1 year, whichever comes first (page 69). The manual also lists general BX tractor greasing every 50 hours on the same page. Following these intervals keeps airflow and lubrication on schedule.
When does the mower drive belt need replacing, and how do I fix a slipping belt?
Replace the mower drive belt once surface splits appear at more than 3 positions (page 439). For a squealing or slipping belt, confirm each pulley spins freely and the belt seats in every groove, then torque the pulley boss mounting nut to 24 to 27 N·m, 2.4 to 2.8 kgf·m, 18 to 20 lbf·ft (page 426). Mower troubleshooting begins on page 424.
Can I print specific sections of this Kubota BX1880-AU & variants manual?
Yes. The PDF carries no DRM, so you can print any page or section your shop needs. It works with any standard printer.
Does this Kubota BX1880-AU & variants Workshop Manual have electrical diagrams?
Yes, fully. The wiring harness diagrams, electrical circuits, and connector pinouts are all here, covering the BX tractor and RCK60D-26BX.
Document Quality
This document is a scanned PDF, not a native digital file. An OCR layer has been applied, allowing you to search and copy the full text, which appears crisp and easy to read. Diagrams and illustrations are raster images, but they are clear with all labels readable. The pages are clean with no noticeable scan artifacts, stains, marks, or skewed content. There are several blank filler pages throughout the document that only contain page numbers and footer information.
Reviews
There are no reviews yet.