Within the hour you could be greasing fittings or checking break-in procedures on your compact tractor, working straight out of this Ford 1220 operator manual PDF, 68 pages of factory publication 42122010. Lubrication and maintenance takes up roughly a third of the book, with separate service charts for two-wheel and four-wheel drive units. Controls, instrument panel indicators, transmission and PTO operation, differential lock use, wheel tread settings, and tractor weighting each get their own walkthrough. Refill the transmission, rear axle and hydraulic system with 16.9 U.S. quarts (16 liters), clean the fuel filter every 100 hours, and change that oil at 300 hours. A forum torque guess can walk a wheel loose. The factory figure printed here is 43 to 53 lbs. ft. for 2WD front hubs. Bookmarked and text searchable, the PDF puts the right chart in front of you in seconds, even with hay down and rain coming.
What's Inside This Ford 1220 Operator Manual
| System | Pages | Key Topics |
|---|---|---|
| International Symbols | 5 | Engine Speed, Engine Oil Pressure, Parking Brake, Differential Lock, Power Take-Off, Battery |
| Safety Precautions | 6-7 | The Tractor |
| Controls and Instruments | 8-14 | Seat, Seat Belt and ROPS, Lighting, Instrument Panel, Throttle Controls, Brake Controls, Differential Control, Mechanical Transmission and PTO Controls |
| Operation | 15-27 | Break-In Procedures, Starting the Engine, Stopping the Engine, Operating the Mechanical and Hydrostatic Transmissions, Four-Wheel Drive and PTO, Towing the Tractor |
| Lubrication and Maintenance | 28-50 | Lubrication and Maintenance Chart (Two-Wheel Drive, Four-Wheel Drive), Fuel and Lubricants, Fuel and Lubricant Service Procedures, Tractor Storage |
| Specifications | 51-54 | Engine, Cooling System, Electrical System, Fuel System, Hydraulic Lift System, Steering |
| Safety and Instruction Decals | 55-62 | Warning Decals, Instruction Decals, Starter Switch, Speed Set Control, Ground Speed Diagram, Remote Control Valve |
| Predelivery and 50-Hour Service | 63-68 | Inoperative Service Checks, Operative Service Checks, Safety Items Checks, Performance Service Checks |
Quick Reference Specifications
| Specification | Value | Page |
|---|---|---|
| Front wheel hub bolts (2WD) | 43-53 lbs. ft. (58-73 N.m.) | p. 43 |
| Fuel filter cleaning interval | 100 hours | p. 34 |
| Diesel fuel filter change interval | 200 hours | p. 32 |
| Transmission, Rear Axle and Hydraulic System oil change interval | 300 hours | p. 36 |
| Transmission, Rear Axle and Hydraulic System Oil (Mechanical Transmission) | 16.9 U.S. Qts. (14.1 Imp. Qts.) (16 Liters) | p. 52 |
| H.S.T. Rear Axle and Transmission | 16.9 U.S. Qts. (14.1 Imp. Qts.) (16 Liters) | p. 52 |
| Engine Oil Change Interval | 100 hours | p. 33 |
| Engine Oil Filter Change Interval | 200 hours | p. 33 |
| Transmission/Rear Axle Oil Change Interval | 300 hours | p. 36 |
| Hydraulic System Oil Filter Change Interval | 300 hours | p. 37 |
| Valve Clearance (Intake) | 0.008 in. (0.20 mm) | p. 52 |
| Valve Clearance (Exhaust) | 0.008 in. (0.20 mm) | p. 52 |
Ford 1220 Common Problems This Manual Covers
Three-point hitch will not hold position, mounted implement settles to the ground overnight
Check the transmission and rear axle oil level; the hitch draws from that reservoir and low oil lets an implement settle. Fill to the mark, full capacity is 16.9 U.S. quarts (16 liters) per page 52, and change the oil every 300 hours as scheduled on page 36. Inspect lower link pins for wear and replace loose ones.
Manual Section: Lubrication and Maintenance p. 36Oil pressure warning light stays on after startup or flickers at low idle when engine is warm
Check the oil level on the dipstick with the engine shut off and the tractor on level ground. Fill to the full mark if low, and keep the 100 hour oil change interval on page 33 with a new filter every 200 hours. If the light stays on with oil correct, stop and call your dealer.
Manual Section: Engine Oil Pressure WarningFrequently Asked Questions
What are the torque specifications for the front wheel disc to hub bolts on a Ford 1220 tractor?
After changing the front wheel tread setting, the wheel disc to hub bolts should be torqued to 43-54 lbs. ft. (58-73 N.m). p. 23
How do you fix ford 1220 cranks but will not start after a fuel filter change or running the tank dry?
Bleed the fuel system; air trapped after a filter change or an empty tank stops fuel delivery cold. Follow the bleeding procedure starting on page 34 and open the bleed points until fuel flows free of bubbles. Clean the filter every 100 hours and replace it every 200 hours to stay ahead of this during planting. p. 34
How do you fix engine turns over slowly and will not fire on cold mornings, hard starting below freezing?
Check the cold weather starting procedure on page 15 and follow it step by step, preheat included, before you crank again. Verify the battery connections are clean and tight and the battery is fully charged. Thick, worn out engine oil drags a cold starter down, so hold the 100 hour oil change interval listed on page 33. p. 15
How do you fix turn the key and nothing happens, no dash lights, no crank, completely dead?
Check the battery cables first: pull both terminals, scrub them bright, and retighten. Verify the ignition switch and instrument panel connections shown on page 8, then test the safety interlocks with the clutch pedal held fully down and the PTO disengaged. Run the inoperative checks from the 50 hour service section on page 63. p. 8
Is this Ford 1220 manual a PDF I download?
This is a 68-page searchable PDF ready for immediate download. Works on any device, so pull it up on your phone while you're under the hood. No shipping, no waiting.
Can I print this Ford 1220 manual?
Yes. The PDF has no DRM restrictions, so print any page or section you need for your shop. Works with any standard printer.
Reviews
There are no reviews yet.